0027126: Create command checktrinfo to verify meshes

[occt.git] / dox / dev_guides / tests / tests.md

 Automated Testing System  {#occt_dev_guides__tests}
======================================

@tableofcontents

@section testmanual_intro Introduction

This document provides OCCT developers and contributors with an overview and practical guidelines for work with OCCT automatic testing system.

Reading the Introduction should be sufficient for developers to use the test system to control non-regression of the modifications they implement in OCCT. Other sections provide a more in-depth description of the test system, required for modifying the tests and adding new test cases. 

@subsection testmanual_intro_basic Basic Information

OCCT automatic testing system is organized around @ref occt_user_guides__test_harness "DRAW Test Harness", a console application based on Tcl (a scripting language) interpreter extended by OCCT-related commands.

Standard OCCT tests are included with OCCT sources and are located in subdirectory *tests* of the OCCT root folder. Other test folders can be included in the test system, e.g. for testing applications based on OCCT.

The tests are organized in three levels:

  * Group: a group of related test grids, usually testing a particular OCCT functionality (e.g. blend);
  * Grid: a set of test cases within a group, usually aimed at testing some particular aspect or mode of execution of the relevant functionality (e.g. buildevol);
  * Test case: a script implementing an individual test (e.g. K4).
  
See @ref testmanual_5_1 "Test Groups" chapter for the current list of available test groups and grids.

Some tests involve data files (typically CAD models) which are located separately and are not included with OCCT code. The archive with publicly available test data files should be downloaded and installed independently on OCCT sources (see http://dev.opencascade.org).

@subsection testmanual_1_2 Intended Use of Automatic Tests

Each modification made in OCCT code must be checked for non-regression 
by running the whole set of tests. The developer who makes the modification 
is responsible for running and ensuring non-regression for the tests available to him.

Note that many tests are based on data files that are confidential and thus available only at OPEN CASCADE. 
The official certification testing of each change before its integration to master branch of official OCCT Git repository (and finally to the official release) is performed by OPEN CASCADE to ensure non-regression on all existing test cases and supported platforms.

Each new non-trivial modification (improvement, bug fix, new feature) in OCCT should be accompanied by a relevant test case suitable for verifying that modification. This test case is to be added by the developer who provides the modification.

If a modification affects the result of an existing test case, either the modification should be corrected (if it causes regression) or the affected test cases should be updated to account for the modification. 

The modifications made in the OCCT code and related test scripts should be included in the same integration to the master branch.

@subsection testmanual_1_3 Quick Start

@subsubsection testmanual_1_3_1 Setup

Before running tests, make sure to define environment variable *CSF_TestDataPath* pointing to the directory containing test data files. 

For this it is recommended to add a file *DrawAppliInit* in the directory which is current at the moment of starting DRAWEXE (normally it is OCCT root directory, <i>$CASROOT </i>). This file is evaluated automatically at the DRAW start. 

Example (Windows)

~~~~~{.tcl}
set env(CSF_TestDataPath) $env(CSF_TestDataPath)\;d:/occt/test-data
~~~~~

Note that variable *CSF_TestDataPath* is set to default value at DRAW start, pointing at the folder <i>$CASROOT/data</i>. 
In this example, subdirectory <i>d:/occt/test-data</i> is added to this path. Similar code could be used on Linux and Mac OS X except that on non-Windows platforms colon ":" should be used as path separator instead of semicolon ";".

All tests are run from DRAW command prompt (run *draw.bat* or *draw.sh* to start it).

@subsubsection testmanual_1_3_2 Running Tests

To run all tests, type command *testgrid* 

Example:

~~~~~
Draw[]> testgrid
~~~~~

To run only a subset of test cases, give masks for group, grid, and test case names to be executed.
Each argument is a list of file masks separated with commas or spaces; by default "*" is assumed.

Example:

~~~~~
Draw[]> testgrid bugs caf,moddata*,xde
~~~~~

As the tests progress, the result of each test case is reported. 
At the end of the log a summary of test cases is output, 
including the list of detected regressions and improvements, if any. 


Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    Tests summary

    CASE 3rdparty export A1: OK 
    ...
    CASE pipe standard B1: BAD (known problem)
    CASE pipe standard C1: OK
    No regressions 
    Total cases: 208 BAD, 31 SKIPPED, 3 IMPROVEMENT, 1791 OK
    Elapsed time: 1 Hours 14 Minutes 33.7384512019 Seconds
    Detailed logs are saved in D:/occt/results_2012-06-04T0919
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

The tests are considered as non-regressive if only OK, BAD (i.e. known problem), and SKIPPED (i.e. not executed, typically because of lack of a data file) statuses are reported. See @ref testmanual_details_results "Interpretation of test results" for details.

The results and detailed logs of the tests are saved by default to a new subdirectory of the subdirectory *results* in the current folder, whose name is generated automatically using the current date and time, prefixed by Git branch name (if Git is available and current sources are managed by Git).
If necessary, a non-default output directory can be specified using option <i> -outdir</i> followed by a path to the directory. This directory should be new or empty; use option <i>-overwrite</i> to allow writing results in the existing non-empty directory. 

Example:
~~~~~
Draw[]> testgrid -outdir d:/occt/last_results -overwrite
~~~~~
In the output directory, a cumulative HTML report <i>summary.html</i> provides links to reports on each test case. An additional report in JUnit-style XML format can be output for use in Jenkins or other continuous integration system.

To re-run test cases which were detected as regressions on previous run, option <i>-regress dirname</i> should be used.
<i>dirname</i> is path to directory containing results of previous run. Only test cases with *FAILED* and *IMPROVEMENT* statuses will be tested.

Example:
~~~~~
Draw[]> testgrid -regress d:/occt/last_results
~~~~~

Type <i>help testgrid</i> in DRAW prompt to get help on options supported by *testgrid* command:

~~~~~
Draw[3]> help testgrid
testgrid: Run all tests, or specified group, or one grid
    Use: testgrid [groupmask [gridmask [casemask]]] [options...]
    Allowed options are:
    -parallel N: run N parallel processes (default is number of CPUs, 0 to disable)
    -refresh N: save summary logs every N seconds (default 60, minimal 1, 0 to disable)
    -outdir dirname: set log directory (should be empty or non-existing)
    -overwrite: force writing logs in existing non-empty directory
    -xml filename: write XML report for Jenkins (in JUnit-like format)
    -beep: play sound signal at the end of the tests
    -regress dirname: re-run only a set of tests that have been detected as regressions on some previous run.
                      Here "dirname" is path to directory containing results of previous run.
    Groups, grids, and test cases to be executed can be specified by list of file 
    masks, separated by spaces or comma; default is all (*).
~~~~~

@subsubsection testmanual_1_3_3 Running a Single Test

To run a single test, type command *test* followed by names of group, grid, and test case. 

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    Draw[1]> test blend simple A1
    CASE blend simple A1: OK
    Draw[2]>
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note that normally an intermediate output of the script is not shown. The detailed log of the test can be obtained after the test execution by running command <i>"dlog get"</i>. 

To see intermediate commands and their output during the test execution, add one more argument 
<i>"echo"</i> at the end of the command line. Note that with this option the log is not collected and summary is not produced.

Type <i>help test</i> in DRAW prompt to get help on options supported by *test* command:

~~~~~
Draw[3]> help test
test: Run specified test case
 Use: test group grid casename [options...]
 Allowed options are:
 -echo: all commands and results are echoed immediately,
        but log is not saved and summary is not produced
        It is also possible to use "1" instead of "-echo"
        If echo is OFF, log is stored in memory and only summary
        is output (the log can be obtained with command "dlog get")
 -outfile filename: set log file (should be non-existing),
        it is possible to save log file in text file or
        in html file(with snapshot), for that "filename"
        should have ".html" extension
 -overwrite: force writing log in existing file
 -beep: play sound signal at the end of the test
 -errors: show all lines from the log report that are recognized as errors
        This key will be ignored if the "-echo" key is already set.
~~~~~

@subsubsection testmanual_intro_quick_create Creating a New Test

The detailed rules of creation of new tests are given in @ref testmanual_3 "Creation and modification of tests" chapter. The following short description covers the most typical situations:

Use prefix <i>bug</i> followed by Mantis issue ID and, if necessary, additional suffixes, for naming the test script, data files, and DRAW commands specific for this test case.

1.	If the test requires C++ code, add it as new DRAW command(s) in one of files in *QABugs* package. 
2.	Add script(s) for the test case in the subfolder corresponding to the relevant OCCT module of the group *bugs* <i>($CASROOT/tests/bugs)</i>. See @ref testmanual_5_2 "the correspondence map".
3.	In the test script:
	*	Load all necessary DRAW modules by command *pload*.
	*	Use command *locate_data_file* to get a path to data files used by test script. (Make sure to have this command not inside catch statement if it is used.)
	*	Use DRAW commands to reproduce the situation being tested.
	*	Make sure that in case of failure the test produces message containing word "Error" or other recognized by test system as error (add new error patterns in file parse.rules if necessary).
	*	If test case reports error due to existing problem and the fix is not available, add @ref testmanual_3_6 "TODO" statement for each error to mark it as known problem. The TODO statements must be specific so as to match the actually generated messages but not all similar errors.
	*	To check expected output which should be obtained as a result of a test, add @ref testmanual_3_7 "REQUIRED" statement for each line of output to mark it as required.
	*	If test case produces error messages (contained in parse.rules) which are expected in that test and should not be considered as its failure (e.g. test for checkshape command), add REQUIRED statement for each error to mark it as required output.
4.	If the test uses data file(s) not yet present in the test database, these can be put to (sub)directory pointed out by *CSF_TestDataPath* variable for running test. The files should be attached to Mantis issue corresponding to the modification being tested.
5.	Check that the test case runs as expected (test for fix: OK with the fix, FAILED without the fix; test for existing problem: BAD), and integrate to Git branch created for the issue.

Example:

* Added files:

~~~~~
git status -short
A tests/bugs/heal/data/bug210_a.brep
A tests/bugs/heal/data/bug210_b.brep
A tests/bugs/heal/bug210_1
A tests/bugs/heal/bug210_2
~~~~~

* Test script

~~~~~{.tcl}
puts "OCC210 (case 1): Improve FixShape for touching wires"

restore [locate_data_file bug210_a.brep] a 

fixshape result a 0.01 0.01
checkshape result
~~~~~

@section testmanual_2 Organization of Test Scripts

@subsection testmanual_2_1 General Layout

Standard OCCT tests are located in subdirectory tests of the OCCT root folder ($CASROOT).

Additional test folders can be added to the test system by defining environment variable *CSF_TestScriptsPath*. This should be list of paths separated by semicolons (*;*) on Windows 
or colons (*:*) on Linux or Mac. Upon DRAW launch, path to *tests* subfolder of OCCT is added at the end of this variable automatically. 

Each test folder is expected to contain:
  * Optional file *parse.rules* defining patterns for interpretation of test results, common for all groups in this folder
  * One or several test group directories. 

Each group directory contains:

  * File *grids.list* that identifies this test group and defines list of test grids in it.
  * Test grids (sub-directories), each containing set of scripts for test cases, and optional files *cases.list*, *parse.rules*, *begin* and *end*.
  * Optional sub-directory data

By convention, names of test groups, grids, and cases should contain no spaces and be lower-case. 
The names *begin, end, data, parse.rules, grids.list* and *cases.list* are reserved. 

General layout of test scripts is shown in Figure 1.

@image html /dev_guides/tests/images/tests_image001.png "Layout of tests folder"
@image latex /dev_guides/tests/images/tests_image001.png "Layout of tests folder"


@subsection testmanual_2_2 Test Groups

@subsubsection testmanual_2_2_1 Group Names

The names of directories of test groups containing systematic test grids correspond to the functionality tested by each group.

Example:

~~~~~
  caf
  mesh
  offset
~~~~~

Test group *bugs* is used to collect the tests coming from bug reports. Group *demo* collects tests of the test system, DRAW, samples, etc.

@subsubsection testmanual_2_2_2 File "grids.list" 

This test group contains file *grids.list*, which defines an ordered list of grids in this group in the following format:

~~~~~~~~~~~~~~~~~
001 gridname1
002 gridname2
...
NNN gridnameN
~~~~~~~~~~~~~~~~~

Example:

~~~~~~~~~~~~~~~~~
    001 basic
    002 advanced
~~~~~~~~~~~~~~~~~

@subsubsection testmanual_2_2_3 File "begin"

This file is a Tcl script. It is executed before every test in the current group. 
Usually it loads necessary Draw commands, sets common parameters and defines 
additional Tcl functions used in test scripts.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    pload TOPTEST ;# load topological command
    set cpulimit 300 ;# set maximum time allowed for script execution
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

@subsubsection testmanual_2_2_4 File "end"

This file is a TCL script. It is executed after every test in the current group. Usually it checks the results of script work, makes a snap-shot of the viewer and writes *TEST COMPLETED* to the output.

Note: *TEST COMPLETED* string should be present in the output to indicate that the test is finished without crash. 

See @ref testmanual_3 "Creation and modification of tests" chapter for more information.

Example:
~~~~~
    if { [isdraw result] } {
        checkshape result
    } else {
        puts "Error: The result shape can not be built"
    }
    puts "TEST COMPLETED"
~~~~~

@subsubsection testmanual_2_2_5 File "parse.rules"

The test group may contain *parse.rules* file. This file defines patterns used for analysis of the test execution log and deciding the status of the test run. 

Each line in the file should specify a status (single word), followed by a regular expression delimited by slashes (*/*) that will be matched against lines in the test output log to check if it corresponds to this status.

The regular expressions should follow <a href="http://www.tcl.tk/man/tcl/TclCmd/re_syntax.htm">Tcl syntax</a>, with special exception that "\b" is considered as word limit (Perl-style), in addition to "\y" used in Tcl.

The rest of the line can contain a comment message, which will be added to the test report when this status is detected.

Example:

~~~~~
    FAILED /\b[Ee]xception\b/ exception
    FAILED /\bError\b/ error
    SKIPPED /Cannot open file for reading/ data file is missing
    SKIPPED /Could not read file .*, abandon/ data file is missing
~~~~~

Lines starting with a *#* character and blank lines are ignored to allow comments and spacing.

See @ref testmanual_details_results "Interpretation of test results" chapter for details.

If a line matches several rules, the first one applies. Rules defined in the grid are checked first, then rules in the group, then rules in the test root directory. This allows defining some rules on the grid level with status *IGNORE* to ignore messages that would otherwise be treated as errors due to the group level rules.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    FAILED /\\bFaulty\\b/ bad shape
    IGNORE /^Error [23]d = [\d.-]+/ debug output of blend command
    IGNORE /^Tcl Exception: tolerance ang : [\d.-]+/ blend failure
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

@subsubsection testmanual_2_2_6  Directory "data"
The test group may contain subdirectory *data*, where test scripts shared by different test grids can be put. See also @ref testmanual_2_3_5 "Directory data".

@subsection testmanual_2_3 Test Grids

@subsubsection testmanual_2_3_1 Grid Names

The folder of a test group  can have several sub-directories (Grid 1… Grid N) defining test grids. 
Each directory contains a set of related test cases. The name of a directory should correspond to its contents.

Example:

~~~~~
caf
   basic
   bugs
   presentation
~~~~~

Here *caf* is the name of the test group and *basic*, *bugs*, *presentation*, etc. are the names of grids.

@subsubsection testmanual_2_3_2 File "begin"

This file is a TCL script executed before every test in the current grid. 

Usually it sets variables specific for the current grid.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    set command bopfuse ;# command tested in this grid
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

@subsubsection testmanual_2_3_3 File "end"

This file is a TCL script executed after every test in current grid. 

Usually it executes a specific sequence of commands common for all tests in the grid.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    vdump $imagedir/${casename}.png ;# makes a snap-shot of AIS viewer
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

@subsubsection testmanual_2_3_4 File "cases.list"

The grid directory can contain an optional file cases.list 
defining an alternative location of the test cases. 
This file should contain a single line defining the relative path to the collection of test cases.

Example:

~~~~~
../data/simple
~~~~~

This option is used for creation of several grids of tests with the same data files and operations but performed with differing parameters. The common scripts are usually located place in the common 
subdirectory of the test group, <i>data/simple</i> for example.

If file *cases.list*  exists, the grid directory should not contain any test cases. 
The specific parameters and pre- and post-processing commands 
for test execution in this grid should be defined in the files *begin* and *end*.


@subsubsection testmanual_2_3_5  Directory "data"

The test grid may contain subdirectory *data*, containing data files used in tests (BREP, IGES, STEP, etc.) of this grid.

@subsection testmanual_2_4 Test Cases

The test case is a TCL script, which performs some operations using DRAW commands 
and produces meaningful messages that can be used to check the validity of the result.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    pcylinder c1 10 20 ;# create first cylinder
    pcylinder c2 5 20 ;# create second cylinder
    ttranslate c2 5 0 10 ;# translate second cylinder to x,y,z
    bsection result c1 c2 ;# create a section of two cylinders
    checksection result ;# will output error message if result is bad
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

The test case can have any name (except for the reserved names *begin, end, data, cases.list* and  *parse.rules*). 
For systematic grids it is usually a capital English letter followed by a number.

Example:

~~~~~
    A1
    A2
    B1
    B2
~~~~~

Such naming facilitates compact representation of tests execution results in tabular format within HTML reports.


@section testmanual_3 Creation And Modification Of Tests

This section describes how to add new tests and update existing ones.

@subsection testmanual_3_1 Choosing Group, Grid, and Test Case Name

The new tests are usually added in the frame of processing issues in OCCT Mantis tracker. 
Such tests in general should be added to group bugs, in the grid 
corresponding to the affected OCCT functionality. See @ref testmanual_5_2 "Mapping of OCCT functionality to grid names in group bugs".

New grids can be added as necessary to contain tests for the functionality not yet covered by existing test grids. 
The test case name in the bugs group should be prefixed by the ID of the corresponding issue in Mantis (without leading zeroes) with prefix *bug*. It is recommended to add a suffix providing a hint on the tested situation. If more than one test is added for a bug, they should be distinguished by suffixes; either meaningful or just ordinal numbers.

Example:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.tcl}
    bug12345_coaxial
    bug12345_orthogonal_1
    bug12345_orthogonal_2
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

If the new test corresponds to a functionality already covered by the existing systematic test grid (e.g. group *mesh* for *BRepMesh* issues), this test can be added (or moved later by OCC team) to that grid. 

@subsection testmanual_3_2 Adding Data Files Required for a Test

It is advisable to make self-contained test scripts whenever possible, so as they could be used in the  environments where data files are not available. For that simple geometric objects and shapes can be created using DRAW commands in the test script itself.

If the test requires a data file, it should be put to the directory listed in environment variable *CSF_TestDataPath*.
Alternatively, it can be put to subdirectory *data* of the test grid. 
It is recommended to prefix the data file with the corresponding issue id prefixed by *bug*, e.g. *bug12345_face1.brep*, to avoid possible conflicts with names of existing data files. 

Note that when the test is integrated to the master branch, OCC team will move the data file to the data files repository, to keep OCCT sources repository clean from data files.

When you prepare a test script, try to minimize the size of involved data model. For instance, if the problem detected on a big shape can be reproduced on a single face extracted from that shape, use only that face in the test.


@subsection testmanual_3_3 Adding new DRAW commands

If the test cannot be implemented using available DRAW commands, consider the following possibilities:
* If the existing DRAW command can be extended to enable possibility required for a test in a natural way (e.g. by adding an option to activate a specific mode of the algorithm), this way is recommended. This change should be appropriately documented in a relevant Mantis issue.
* If the new command is needed to access OCCT functionality not exposed to DRAW previously, and this command can be potentially reused (for other tests), it should be added to the package where similar commands are implemented (use *getsource* DRAW command to get the package name). The name and arguments of the new command should be chosen to keep similarity with the existing commands. This change should be documented in a relevant Mantis issue.
* Otherwise the new command implementing the actions needed for this particular test should be added in *QABugs* package. The command name should be formed by the Mantis issue ID prefixed by *bug*, e.g. *bug12345*.

Note that a DRAW command is expected to return 0 in case of a normal completion, and 1 (Tcl exception) if it is incorrectly used (e.g. a wrong number of input arguments). Thus if the new command needs to report a test error, this should be done by outputting an appropriate error message rather than by returning a non-zero value.
File names must be encoded in the script rather than in the DRAW command and passed to the DRAW command as an argument.

@subsection testmanual_3_4 Script Implementation

The test should run commands necessary to perform the tested operations, in general assuming a clean DRAW session. The required DRAW modules should be loaded by *pload* command, if it is not done by *begin* script. The messages produced by commands in a standard output should include identifiable messages on the discovered problems if any. 

Usually the script represents a set of commands that a person would run interactively to perform the operation and see its results, with additional comments to explain what happens.

Example:
~~~~~
# Simple test of fusing box and sphere
box b 10 10 10 
sphere s 5
bfuse result b s
checkshape result
~~~~~

Make sure that file *parse.rules* in the grid or group directory contains a regular expression to catch possible messages indicating the failure of the test. 

For instance, for catching errors reported by *checkshape* command relevant grids define a rule to recognize its report by the word *Faulty*:

~~~~~
FAILED /\bFaulty\b/ bad shape
~~~~~

For the messages generated in the script it is recommended to use the word 'Error' in the error message.

Example:

~~~~~
set expected_length 11
if { [expr $actual_length - $expected_length] > 0.001 } {
    puts "Error: The length of the edge should be $expected_length"
}
~~~~~

At the end, the test script should output *TEST COMPLETED* string to mark a successful completion of the script. This is often done by the *end* script in the grid.

When the test script requires a data file, use Tcl procedure *locate_data_file* to get a path to it, instead of putting the path explicitly. This will allow easy move of the data file from OCCT sources repository to the data files repository without the need to update the test script.

Example:

~~~~~
stepread [locate_data_file CAROSKI_COUPELLE.step] a *
~~~~~

When the test needs to produce some snapshots or other artefacts, use Tcl variable *imagedir* as the location where such files should be put. 
* Command *testgrid* sets this variable to the subdirectory of the results folder corresponding to the grid. 
* Command *test* by default creates a dedicated temporary directory in the system temporary folder (normally the one specified by environment variable *TempDir*, *TEMP*, or *TMP*) for each execution, and sets *imagedir* to that location. 

However if variable *imagedir* is defined on the top level of Tcl interpretor, command *test* will use it instead of creating a new directory.

Use Tcl variable *casename* to prefix all files produced by the test. 
This variable is set to the name of the test case.

The test system can recognize an image file (snapshot) and include it in HTML log and differences if its name starts with the name of the test case (use variable *casename*), optionally followed by underscore or dash and arbitrary suffix.

The image format (defined by extension) should be *png*.

Example:
~~~~~
xwd $imagedir/${casename}.png
vdisplay result; vfit
vdump $imagedir/${casename}-axo.png
vfront; vfit
vdump $imagedir/${casename}-front.png
~~~~~

would produce:
~~~~~
A1.png
A1-axo.png
A1-front.png
~~~~~

Note that OCCT must be built with FreeImage support to be able to produce usable images.

Other Tcl variables defined during the test execution are:
- *groupname*: name of the test group;
- *gridname*: name of the test grid;
- *dirname*: path to the root directory of the current set of test scripts.

In order to ensure that the test works as expected in different environments, observe the following additional rules:
* Avoid using external commands such as *grep, rm,* etc., as these commands can be absent on another system (e.g. on Windows); use facilities provided by Tcl instead.
* Do not put call to *locate_data_file* in catch statement -- this can prevent correct interpretation of the missing data file by the test system.
* Do not use commands *decho* and *dlog* in the test script, to avoid interference with use of these commands by the test system.

@subsection testmanual_details_results Interpretation of test results

The result of the test is evaluated by checking its output against patterns defined in the files *parse.rules* of the grid and group.

The OCCT test system recognizes five statuses of the test execution:
* SKIPPED: reported if a line matching SKIPPED pattern is found (prior to any FAILED pattern). This indicates that the test cannot be run in the current environment; the most typical case is the absence of the required data file.
* FAILED: reported if a line matching pattern with status FAILED is found (unless it is masked by the preceding IGNORE pattern or a TODO or REQUIRED statement), or if message TEST COMPLETED or at least one of REQUIRED patterns is not found. This indicates that the test has produced a bad or unexpected result, and usually means a regression.
* BAD: reported if the test script output contains one or several TODO statements and the corresponding number of matching lines in the log. This indicates a known problem. The lines matching TODO statements are not checked against other patterns and thus will not cause a FAILED status.  
* IMPROVEMENT: reported if the test script output contains a TODO statement for which no corresponding line is found. This is a possible indication of improvement (a known problem has disappeared).
* OK: reported if none of the above statuses have been assigned. This means that the test has passed without problems.

Other statuses can be specified in *parse.rules* files, these will be classified as FAILED.

For integration of the change to OCCT repository, all tests should return either OK or BAD status.
The new test created for an unsolved problem should return BAD. The new test created for a fixed problem should return FAILED without the fix, and OK with the fix.

@subsection testmanual_3_6 Marking BAD cases

If the test produces an invalid result at a certain moment then the corresponding bug should be created in the OCCT issue tracker located at http://tracker.dev.opencascade.org, and the problem should be marked as TODO in the test script.

The following statement should be added to such a test script:
~~~~~
puts "TODO BugNumber ListOfPlatforms: RegularExpression"
~~~~~

Here:
* *BugNumber* is the bug ID in the tracker. For example: #12345.
* *ListOfPlatforms* is a list of platforms, at which the bug is reproduced (Linux, Windows, MacOS, or All). Note that the platform name is custom for the OCCT test system; it corresponds to the value of environment variable *os_type* defined in DRAW.

Example:
~~~~~
Draw[2]> puts $env(os_type)
windows
~~~~~

* RegularExpression is a regular expression, which should be matched against the line indicating the problem in the script output. 

Example:
~~~~~
puts "TODO #22622 Mandriva2008: Abort .* an exception was raised"
~~~~~

The parser checks the test output and if an output line matches the *RegularExpression* then it will be assigned a BAD status instead of FAILED.

A separate TODO line must be added for each output line matching an error expression to mark the test as BAD. If not all TODO messages are found in the test log, the test will be considered as possible improvement.

To mark the test as BAD for an incomplete case (when the final *TEST COMPLETE* message is missing) the expression *TEST INCOMPLETE* should be used instead of the regular expression. 

Example:

~~~~~
puts "TODO OCC22817 All: exception.+There are no suitable edges"
puts "TODO OCC22817 All: \\*\\* Exception \\*\\*"
puts "TODO OCC22817 All: TEST INCOMPLETE"
~~~~~

@subsection testmanual_3_7 Marking required output

To check expected output which must be obtained as a result of a test for it to be considered correct, add REQUIRED statement for each specific message.
For that, the following statement should be added to such a test script:

~~~~~
puts "REQUIRED ListOfPlatforms: RegularExpression"
~~~~~

Here *ListOfPlatforms* and *RegularExpression* have the same meaning as in TODO statements described above.

The REQUIRED statement can also be used to mask message that would normally be interpreted as error (according to rules defined in *parse.rules*) but should not be considered as such within current test.

Example:
~~~~~
puts "REQUIRED Linux: Faulty shapes in variables faulty_1 to faulty_5"
~~~~~

This statement notifies test system that errors reported by *checkshape* command are expected in that test case, and test should be considered as OK if this message appears, despite of presence of general rule stating that 'Faulty' signals failure.

If output does not contain required statement, test case will be marked as FAILED.

@section testmanual_4 Advanced Use

@subsection testmanual_4_1 Running Tests on Older Versions of OCCT

Sometimes it might be necessary to run tests on the previous versions of OCCT (<= 6.5.4) that do not include this test system. This can be done by adding DRAW configuration file *DrawAppliInit* in the directory, which is current by the moment of DRAW start-up, to load test commands and to define the necessary environment.

Note: in OCCT 6.5.3, file *DrawAppliInit* already exists in <i>$CASROOT/src/DrawResources</i>, new commands should be added to this file instead of a new one in the current directory.

For example, let us assume that *d:/occt* contains an up-to-date version of OCCT sources with tests, and the test data archive is unpacked to *d:/test-data*):

~~~~~
set env(CASROOT) d:/occt
set env(CSF_TestScriptsPath) $env(CASROOT)/tests
source $env(CASROOT)/src/DrawResources/TestCommands.tcl
set env(CSF_TestDataPath) $env(CASROOT)/data;d:/test-data
return
~~~~~

Note that on older versions of OCCT the tests are run in compatibility mode and thus not all output of the test command can be captured; this can lead to absence of some error messages (can be reported as either a failure or an improvement).

@subsection testmanual_4_2 Adding custom tests

You can extend the test system by adding your own tests. For that it is necessary to add paths to the directory where these tests are located, and one or more additional data directories, to the environment variables *CSF_TestScriptsPath* and *CSF_TestDataPath*. The recommended way for doing this is using DRAW configuration file *DrawAppliInit* located in the directory which is current by the moment of DRAW start-up.

Use Tcl command <i>_path_separator</i> to insert a platform-dependent separator to the path list.

For example:
~~~~~
set env(CSF_TestScriptsPath) \
  $env(TestScriptsPath)[_path_separator]d:/MyOCCTProject/tests
set env(CSF_TestDataPath) \
  d:/occt/test-data[_path_separator]d:/MyOCCTProject/data
return ;# this is to avoid an echo of the last command above in cout
~~~~~

@subsection testmanual_4_3 Parallel execution of tests

For better efficiency, on computers with multiple CPUs the tests can be run in parallel mode. This is default behavior for command *testgrid* : the tests are executed in parallel processes (their number is equal to the number of CPUs available on the system). In order to change this behavior, use option  parallel followed by the number of processes to be used (1 or 0 to run sequentially).

Note that the parallel execution is only possible if Tcl extension package *Thread* is installed. 
If this package is not available, *testgrid* command will output a warning message.

@subsection testmanual_4_4 Checking non-regression of performance, memory, and visualization

Some test results are very dependent on the characteristics of the workstation, where they are performed, and thus cannot be checked by comparison with some predefined values. These results can be checked for non-regression (after a change in OCCT code) by comparing them with the results produced by the version without this change. The most typical case is comparing the result obtained in a branch created for integration of a fix (CR***) with the results obtained on the master branch before that change is made.

OCCT test system provides a dedicated command *testdiff* for comparing CPU time of execution, memory usage, and images produced by the tests.

~~~~~
testdiff dir1 dir2 [groupname [gridname]] [options...]
~~~~~
Here *dir1* and *dir2* are directories containing logs of two test runs.

Possible options are:
* <i>-save \<filename\> </i> -- saves the resulting log in a specified file (<i>$dir1/diff-$dir2.log</i> by default). HTML log is saved with the same name and extension .html;
* <i>-status {same|ok|all}</i> -- allows filtering compared cases by their status:
	* *same* -- only cases with same status are compared (default);
	* *ok*   -- only cases with OK status in both logs are compared;
	* *all*  -- results are compared regardless of status;
* <i>-verbose \<level\> </i> -- defines the scope of output data:
	* 1 -- outputs only differences;
	* 2 -- additionally outputs the list of logs and directories present in one of directories only;
	* 3 -- (by default) additionally outputs progress messages;

Example:

~~~~~
Draw[]> testdiff results-CR12345-2012-10-10T08:00 results-master-2012-10-09T21:20 
~~~~~

@section testmanual_5 APPENDIX

@subsection testmanual_5_1 Test groups

@subsubsection testmanual_5_1_1 3rdparty

This group allows testing the interaction of OCCT and 3rdparty products.

DRAW module: VISUALIZATION.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| export	| vexport	| export of images to different formats |
| fonts	 | vtrihedron, vcolorscale, vdrawtext	| display of fonts |


@subsubsection testmanual_5_1_2 blend

This group allows testing blends (fillets) and related operations.

DRAW module: MODELING.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| simple	| blend	| fillets on simple shapes |
| complex	| blend 	| fillets on complex shapes, non-trivial geometry |
| tolblend_simple	| tolblend, blend | |
| buildevol	| buildevol	| |
| tolblend_buildvol | 	tolblend, buildevol |	use of additional command tolblend |
| bfuseblend	| bfuseblend	| | 
| encoderegularity	| encoderegularity	| | 

@subsubsection testmanual_5_1_3 boolean

This group allows testing Boolean operations.

DRAW module: MODELING (packages *BOPTest* and *BRepTest*).

Grids names are based on name of the command used, with suffixes: 
* <i>_2d</i> -- for tests operating with 2d objects (wires, wires, 3d objects, etc.); 
* <i>_simple</i> -- for tests operating on simple shapes (boxes, cylinders, toruses, etc.);
* <i>_complex</i> -- for tests dealing with complex shapes.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| bcommon_2d	| bcommon	| Common operation (old algorithm), 2d |
| bcommon_complex	| bcommon	| Common operation (old algorithm), complex shapes |
| bcommon_simple	| bcommon	| Common operation (old algorithm), simple shapes |
| bcut_2d	| bcut | Cut operation (old algorithm), 2d |
| bcut_complex	| bcut	| Cut operation (old algorithm), complex shapes |
| bcut_simple	| bcut |	Cut operation (old algorithm), simple shapes |
| bcutblend	| bcutblend	| | 
| bfuse_2d	| bfuse	| Fuse operation (old algorithm), 2d |
| bfuse_complex	| bfuse |	Fuse operation (old algorithm), complex shapes |
| bfuse_simple	| bfuse	| Fuse operation (old algorithm), simple shapes |
| bopcommon_2d	| bopcommon |	Common operation, 2d |
| bopcommon_complex	| bopcommon	| Common operation, complex shapes | 
| bopcommon_simple	| bopcommon	| Common operation, simple shapes |
| bopcut_2d |	bopcut |	Cut operation, 2d |
| bopcut_complex |	bopcut |	Cut operation, complex shapes |
| bopcut_simple	| bopcut	| Cut operation, simple shapes |
| bopfuse_2d	| bopfuse	| Fuse operation, 2d |
| bopfuse_complex	| bopfuse	| Fuse operation, complex shapes |
| bopfuse_simple	| bopfuse	| Fuse operation, simple shapes |
| bopsection	| bopsection	| Section |
| boptuc_2d	| boptuc	| |
| boptuc_complex	| boptuc	| |
| boptuc_simple	| boptuc	| |
| bsection |	bsection	| Section (old algorithm) |

@subsubsection testmanual_5_1_4 bugs

This group allows testing cases coming from Mantis issues.

The grids are organized following OCCT module and category set for the issue in the Mantis tracker. 
See @ref testmanual_5_2 "Mapping of OCCT functionality to grid names in group bugs" chapter for details.

@subsubsection testmanual_5_1_5 caf

This group allows testing OCAF functionality.

DRAW module: OCAFKERNEL.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| basic	| | 	Basic attributes |
| bugs	| |	Saving and restoring of document |
| driver	| |	OCAF drivers |
| named_shape	| |	*TNaming_NamedShape* attribute |
| presentation	| | *AISPresentation* attributes |
| tree	| |	Tree construction attributes |
| xlink	 | |	XLink attributes |

@subsubsection testmanual_5_1_6 chamfer

This group allows testing chamfer operations.

DRAW module: MODELING.

The test grid name is constructed depending on the type of the tested chamfers. Additional suffix <i>_complex</i> is used for test cases involving complex geometry (e.g. intersections of edges forming a chamfer); suffix <i>_sequence</i> is used for grids where chamfers are computed sequentially.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| equal_dist	| | 	Equal distances from edge |
| equal_dist_complex	| |	Equal distances from edge, complex shapes |
| equal_dist_sequence	| |	Equal distances from edge, sequential operations |
| dist_dist	| |	Two distances from edge |
| dist_dist_complex	| |	Two distances from edge, complex shapes |
| dist_dist_sequence	| |	Two distances from edge, sequential operations |
| dist_angle	| |	Distance from edge and given angle |
| dist_angle_complex	| |	Distance from edge and given angle |
| dist_angle_sequence	| |	Distance from edge and given angle |

@subsubsection testmanual_5_1_7 demo

This group allows demonstrating how testing cases are created, and testing DRAW commands and the test system as a whole.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| draw	|  getsource, restore	| Basic DRAW commands |
| testsystem	| |	Testing system |
| samples	| |	OCCT samples | 


@subsubsection testmanual_5_1_8 draft

This group allows testing draft operations.

DRAW module: MODELING.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| Angle	| depouille	| Drafts with angle (inclined walls) |


@subsubsection testmanual_5_1_9 feat

This group allows testing creation of features on a shape.

DRAW module: MODELING (package *BRepTest*).

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| featdprism		| | |
| featlf		| | |
| featprism		| | |
| featrevol		| | | 
| featrf		| | |

@subsubsection testmanual_5_1_10 heal

This group allows testing the functionality provided by *ShapeHealing* toolkit.

DRAW module: XSDRAW

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| fix_shape	| fixshape	| Shape healing | 
| fix_gaps	| fixwgaps	| Fixing gaps between edges on a wire |
| same_parameter	| sameparameter	| Fixing non-sameparameter edges |
| fix_face_size	| DT_ApplySeq	| Removal of small faces |
| elementary_to_revolution	| DT_ApplySeq	| Conversion of elementary surfaces to revolution |
| direct_faces	| directfaces	| Correction of axis of elementary surfaces | 
| drop_small_edges	| fixsmall	| Removal of small edges | 
| split_angle	| DT_SplitAngle |	Splitting periodic surfaces by angle |
| split_angle_advanced | DT_SplitAngle	| Splitting periodic surfaces by angle |
| split_angle_standard | DT_SplitAngle	| Splitting periodic surfaces by angle |
| split_closed_faces |	DT_ClosedSplit	| Splitting of closed faces |
| surface_to_bspline |	DT_ToBspl	| Conversion of surfaces to b-splines |
| surface_to_bezier | DT_ShapeConvert |	Conversion of surfaces to bezier |
| split_continuity	| DT_ShapeDivide | Split surfaces by continuity criterion |
| split_continuity_advanced | DT_ShapeDivide | Split surfaces by continuity criterion |
| split_continuity_standard | DT_ShapeDivide | Split surfaces by continuity criterion |
| surface_to_revolution_advanced |	DT_ShapeConvertRev	| Convert elementary surfaces to revolutions, complex cases |
| surface_to_revolution_standard |	DT_ShapeConvertRev	| Convert elementary surfaces to revolutions, simple cases |

@subsubsection testmanual_5_1_11 mesh

This group allows testing shape tessellation (*BRepMesh*) and shading.

DRAW modules: MODELING (package *MeshTest*), VISUALIZATION (package *ViewerTest*)

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| advanced_shading	| vdisplay	| Shading, complex shapes |
| standard_shading	| vdisplay	| Shading, simple shapes |
| advanced_mesh	| mesh |	Meshing of complex shapes |
| standard_mesh | mesh |	Meshing of simple shapes |
| advanced_incmesh	| incmesh	| Meshing of complex shapes |
| standard_incmesh	| incmesh	| Meshing of simple shapes |
| advanced_incmesh_parallel | incmesh | Meshing of complex shapes, parallel mode |
| standard_incmesh_parallel | incmesh | Meshing of simple shapes, parallel mode |

@subsubsection testmanual_5_1_12 mkface

This group allows testing creation of simple surfaces.

DRAW module: MODELING (package *BRepTest*)

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| after_trim | mkface	| |
| after_offset | mkface	| |
| after_extsurf_and_offset	| mkface  | |	
| after_extsurf_and_trim | mkface	| | 
| after_revsurf_and_offset | mkface	| | 
| mkplane | mkplane	| |

@subsubsection testmanual_5_1_13 nproject

This group allows testing normal projection of edges and wires onto a face.

DRAW module: MODELING (package *BRepTest*) 

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| Base	| nproject	|  |

@subsubsection testmanual_5_1_14 offset

This group allows testing offset functionality for curves and surfaces.

DRAW module: MODELING (package *BRepTest*) 

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| compshape	| offsetcompshape	| Offset of shapes with removal of some faces | 
| faces_type_a	| offsetparameter, offsetload, offsetperform | Offset on a subset of faces with a fillet |
| faces_type_i 	| offsetparameter, offsetload, offsetperform | 	Offset on a subset of faces with a sharp edge |
| shape_type_a 	| offsetparameter, offsetload, offsetperform | 	Offset on a whole shape with a fillet |
| shape_type_i 	| offsetparameter, offsetload, offsetperform | 	Offset on a whole shape with a fillet |
| shape	 | offsetshape	| |
| wire_closed_outside_0_005, wire_closed_outside_0_025, wire_closed_outside_0_075, wire_closed_inside_0_005, wire_closed_inside_0_025, wire_closed_inside_0_075, wire_unclosed_outside_0_005, wire_unclosed_outside_0_025, wire_unclosed_outside_0_075	|	mkoffset | 2d offset of closed and unclosed planar wires with different offset step and directions of offset ( inside / outside ) |
	
@subsubsection testmanual_5_1_15 pipe

This group allows testing construction of pipes (sweeping of a contour along profile).

DRAW module: MODELING (package *BRepTest*) 

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| Standard	| pipe	| |

@subsubsection testmanual_5_1_16 prism

This group allows testing construction of prisms.

DRAW module: MODELING (package *BRepTest*) 

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| seminf | prism	| |

@subsubsection testmanual_5_1_17 sewing

This group allows testing sewing of faces by connecting edges.

DRAW module: MODELING (package *BRepTest*) 

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| tol_0_01	| sewing | Sewing faces with tolerance 0.01 |
| tol_1	| sewing | Sewing faces with tolerance 1 |
| tol_100 | sewing | Sewing faces with tolerance 100 | 

@subsubsection testmanual_5_1_18 thrusection

This group allows testing construction of shell or a solid passing through a set of sections in a given sequence (loft).

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| solids	| thrusection | Lofting with resulting solid | 
| not_solids | thrusection	| Lofting with resulting shell or face | 

@subsubsection testmanual_5_1_19 xcaf

This group allows  testing extended data exchange packages.

| Grid	| Commands	| Functionality |
| :---- | :----- | :------- | 
| dxc, dxc_add_ACL, dxc_add_CL, igs_to_dxc, igs_add_ACL, brep_to_igs_add_CL, stp_to_dxc, stp_add_ACL, brep_to_stp_add_CL, brep_to_dxc, add_ACL_brep, brep_add_CL	| | Subgroups are divided by format of source file, by format of result file and by type of document modification. For example, *brep_to_igs* means that the source shape in brep format was added to the document, which was saved into igs format after that. The postfix *add_CL* means that colors and layers were initialized in the document before saving and the postfix *add_ACL* corresponds to the creation of assembly and initialization of colors and layers in a document before saving. |
	

@subsection testmanual_5_2 Mapping of OCCT functionality to grid names in group *bugs*

| OCCT Module / Mantis category	| Toolkits	| Test grid in group bugs |
| :---------- | :--------- | :---------- | 
| Application Framework	| PTKernel, TKPShape, TKCDF, TKLCAF, TKCAF, TKBinL, TKXmlL, TKShapeSchema, TKPLCAF, TKBin, TKXml, TKPCAF, FWOSPlugin, TKStdLSchema, TKStdSchema, TKTObj, TKBinTObj, TKXmlTObj | caf |
| Draw	| TKDraw, TKTopTest, TKViewerTest, TKXSDRAW, TKDCAF, TKXDEDRAW, TKTObjDRAW, TKQADraw, DRAWEXE, Problems of testing system |	draw | 
| Shape Healing | TKShHealing | heal |
| Mesh	| TKMesh, TKXMesh | mesh |
| Data Exchange	| TKIGES	| iges |
| Data Exchange	|	TKSTEPBase, TKSTEPAttr, TKSTEP209, TKSTEP |	step |
| Data Exchange	|	TKSTL, TKVRML 	| stlvrml |
| Data Exchange	| TKXSBase, TKXCAF, TKXCAFSchema, TKXDEIGES, TKXDESTEP, TKXmlXCAF, TKBinXCAF | xde |
| Foundation Classes |	TKernel, TKMath	| fclasses |
| Modeling_algorithms |	TKGeomAlgo, TKTopAlgo, TKPrim, TKBO, TKBool, TKHLR, TKFillet, TKOffset, TKFeat, TKXMesh |	modalg |
| Modeling Data | TKG2d, TKG3d, TKGeomBase, TKBRep	| moddata |
| Visualization | TKService, TKV2d, TKV3d, TKOpenGl, TKMeshVS, TKNIS	| vis |


@subsection testmanual_5_3 Recommended approaches to checking test results

@subsubsection testmanual_5_3_1 Shape validity

Run command *checkshape* on the result (or intermediate) shape and make sure that *parse.rules* of the test grid or group reports bad shapes (usually recognized by word "Faulty") as error.

Example
~~~~~
checkshape result
~~~~~

To check the number of faults in the shape command *checkfaults* can be used.

Use: checkfaults shape source_shape [ref_value=0]

The default syntax of *checkfaults* command:
~~~~~
checkfaults results a_1
~~~~~

The command will check the number of faults in the source shape (*a_1*) and compare it
with number of faults in the resulting shape (*result*). If shape *result* contains
more faults, you will get an error:
~~~~~
checkfaults results a_1
Error : Number of faults is 5
~~~~~
It is possible to set the reference value for comparison (reference value is 4):

~~~~~
checkfaults results a_1 4
~~~~~

If number of faults in the resulting shape is unstable, reference value should be set to "-1".
As a result command *checkfaults* will return the following error:

~~~~~
checkfaults results a_1 -1
Error : Number of faults is UNSTABLE
~~~~~

@subsubsection testmanual_5_3_2 Shape tolerance
The maximal tolerance of sub-shapes of each kind of the resulting shape can be extracted from output of tolerance command as follows:

~~~~~
set tolerance [tolerance result]
regexp { *FACE +: +MAX=([-0-9.+eE]+)} $tolerance dummy max_face
regexp { *EDGE +: +MAX=([-0-9.+eE]+)} $tolerance dummy max_edgee
regexp { *VERTEX +: +MAX=([-0-9.+eE]+)} $tolerance dummy max_vertex
~~~~~

It is possible to use command *checkmaxtol* to check maximal tolerance of shape and compare it with reference value.

Use: checkmaxtol shape [options...]

Allowed options are:
 *   -ref: reference value of maximum tolerance
 *   -source: list of shapes to compare with
 *   -min_tol: minimum tolerance for comparison
 *   -multi_tol: tolerance multiplier

The default syntax of *checkmaxtol* command for comparison with the reference value:
~~~~~
checkmaxtol result -ref 0.00001
~~~~~

There is an opportunity to compare max tolerance of resulting shape with max tolerance of source shape.
In the following example command *checkmaxtol* gets max tolerance among objects *a_1* and *a_2*.
Then it chooses the maximum value between founded tolerance and value -min_tol (0.000001)
and multiply it on the coefficient -multi_tol (i.e. 2):

~~~~~
checkmaxtol result -source {a_1 a_2} -min_tol 0.000001 -multi_tol 2
~~~~~

If the value of maximum tolerance more than founded tolerance for comparison, the command will return an error.

Also, command *checkmaxtol* can be used to get max tolerance of the shape:

~~~~~
set maxtol [checkmaxtol result]
~~~~~

@subsubsection testmanual_5_3_3 Shape volume, area, or length

Use command *vprops, sprops,* or *lprops* to correspondingly measure volume, area, or length of the shape produced by the test. The value can be extracted from the result of the command by *regexp*.

Example:
~~~~~
# check area of shape result with 1% tolerance
regexp {Mass +: +([-0-9.+eE]+)} [sprops result] dummy area
if { abs($area - $expected) > 0.1 + 0.01 * abs ($area) } {
    puts "Error: The area of result shape is $area, while expected $expected"
}
~~~~~

@subsubsection testmanual_5_3_4 Memory leaks

The test system measures the amount of memory used by each test case, and considerable deviations (as well as overall difference) comparing with reference results will be reported by *testdiff* command.

The typical approach to checking memory leak on a particular operation is to run this operation in cycle measuring memory consumption at each step and comparing it with some threshold value. Note that file begin in group bugs defines command *checktrend* that can be used to analyze a sequence of memory measurements to get statistically based evaluation of the leak presence.

Example: 
~~~~~
set listmem {}
for {set i 1} {$i < 100} {incr i} {
    # run suspect operation 
    …
    # check memory usage (with tolerance equal to half page size)
    lappend listmem [expr [meminfo w] / 1024]
    if { [checktrend $listmem 0 256 "Memory leak detected"] } {
        puts "No memory leak, $i iterations"
        break
    }
}
~~~~~

@subsubsection testmanual_5_3_5 Visualization

Take a snapshot of the viewer, give it the name of the test case, and save in the directory indicated by Tcl variable *imagedir*. 

~~~~~
vinit
vclear
vdisplay result
vsetdispmode 1
vfit
vzfit
vdump $imagedir/${casename}_shading.png
~~~~~

This image will be included in the HTML log produced by *testgrid* command and will be checked for non-regression through comparison of images by command *testdiff*.

Also it is possible to use command *checkview* to make a snapshot of the viewer.

Use: checkview [options...]
Allowed options are:
*   -display shapename: display shape with name 'shapename'
*   -3d: display shape in 3d viewer
*   -2d [ v2d / smallview ]: display shape in 2d viewer (default viewer is a 'smallview')
*   -path PATH: location of saved screenshot of viewer
*   -vdispmode N: it is possible to set vdispmode for 3d viewer (default value is 1)
*   -screenshot: procedure will try to make screenshot of already created viewer
*   Procedure can check some property of shape (length, area or volume) and compare it with some value N:
	* -l [N]
	* -s [N]
	* -v [N]
	* If current property is equal to value N, shape is marked as valid in procedure.
	* If value N is not given procedure will mark shape as valid if current property is non-zero.
*   -with {a b c}: display shapes 'a' 'b' 'c' together with 'shape' (if shape is valid)
*   -otherwise {d e f}: display shapes 'd' 'e' 'f' instead of 'shape' (if shape is NOT valid)

Note that one of two options -2d/-3d is required.

Examples:
~~~~~
checkview -display result -2d -path ${imagedir}/${test_image}.png
checkview -display result -3d -path ${imagedir}/${test_image}.png
checkview -display result_2d -2d v2d -path ${imagedir}/${test_image}.png
~~~~~
~~~~~
box a 10 10 10
box b 5 5 5 10 10 10
bcut result b a
set result_vertices [explode result v]
checkview -display result -2d -with ${result_vertices} -otherwise { a b } -l -path ${imagedir}/${test_image}.png
~~~~~
~~~~~
box a 10 10 10
box b 5 5 5 10 10 10
bcut result b a
vinit
vdisplay a b
vfit
checkview -screenshot -3d -path ${imagedir}/${test_image}.png
~~~~~

@subsubsection testmanual_5_3_6 Number of free edges

To check the number of free edges run the command *checkfreebounds*.

It compares number of free edges with reference value.

Use: checkfreebounds shape ref_value [options...]

Allowed options are:
 * -tol N: used tolerance (default -0.01)
 * -type N: used type, possible values are "closed" and "opened" (default "closed")

~~~~~
checkfreebounds result 13
~~~~~

Option -tol N is used to set tolerance for command *freebounds*, which is used within command *checkfreebounds*.

Option -type N is used to select the type of counted free edges - closed or opened.

If the number of free edges in the resulting shape is unstable, reference value should be set to "-1".
As a result command *checkfreebounds* will return the following error:

~~~~~
checkfreebounds result -1
Error : Number of free edges is UNSTABLE
~~~~~

@subsubsection testmanual_5_3_7 Compare numbers

Procedure to check equality of two reals with some tolerance (relative and absolute)

Use: checkreal name value expected tol_abs tol_rel

~~~~~
checkreal "Some important value" $value 5 0.0001 0.01
~~~~~

@subsubsection testmanual_5_3_8 Check number of sub-shapes

Compare number of sub-shapes in "shape" with given reference data

Use: checknbshapes shape [options...]
Allowed options are:
 * -vertex N
 * -edge N
 * -wire N
 * -face N
 * -shell N
 * -solid N
 * -compsolid N
 * -compound N
 * -shape N
 * -t: compare the number of sub-shapes in "shape" counting
      the same sub-shapes with different location as different sub-shapes.
 * -m msg: print "msg" in case of error

~~~~~
checknbshapes result -vertex 8 -edge 4
~~~~~

@subsubsection testmanual_5_3_9 Check pixel color

To check pixel color command *checkcolor* can be used.

Use: checkcolor x y red green blue

  x, y -- pixel coordinates

  red green blue -- expected pixel color (values from 0 to 1)

This procedure checks color with tolerance (5x5 area)

Next example will compare color of point with coordinates x=100 y=100 with RGB color R=1 G=0 B=0.
If colors are not equal, procedure will check the nearest ones points (5x5 area)
~~~~~
checkcolor 100 100 1 0 0
~~~~~

@subsubsection testmanual_5_3_10 Compute length, area and volume of input shape

Procedure *checkprops* computes length, area and volume of input shape.

Use: checkprops shapename [options...]

Allowed options are:
 * -l LENGTH: command lprops, computes the mass properties of all edges in the shape with a linear density of 1
 * -s AREA: command sprops, computes the mass properties of all faces with a surface density of 1 
 * -v VOLUME: command vprops, computes the mass properties of all solids with a density of 1
 * -eps EPSILON: the epsilon defines relative precision of computation
 * -equal SHAPE: compare area\volume\length of input shapes. Puts error if its are not equal
 * -notequal SHAPE: compare area\volume\length of input shapes. Puts error if its are equal

Options -l, -s and -v are independent and can be used in any order. Tolerance epsilon is the same for all options.

~~~~~
checkprops result -s 6265.68 
checkprops result -s -equal FaceBrep
~~~~~

@subsubsection testmanual_5_3_11 Parse output dump and compare it with reference values

Procedure *checkdump* is used to parse output dump and compare it with reference values.

Use: checkdump shapename [options...]

Allowed options are:
 * -name NAME: list of parsing parameters (e.g. Center, Axis, etc)
 * -ref VALUE: list of reference values for each parameter in NAME 
 * -eps EPSILON: the epsilon defines relative precision of computation

~~~~~
checkdump result -name {Center Axis XAxis YAxis Radii} -ref {{-70 0} {-1 -0} {-1 -0} {0 -1} {20 10}} -eps 0.01
~~~~~

@subsubsection testmanual_5_3_12 Compute length of input curve

Procedure *checklength* computes length of input curve.

Use: checklength curvename [options...]
  
Allowed options are:
 * -l LENGTH: command length, computes the length of input curve with precision of computation
 * -eps EPSILON: the epsilon defines relative precision of computation
 * -equal CURVE: compare length of input curves. Puts error if its are not equal
 * -notequal CURVE: compare length of input curves. Puts error if its are equal

~~~~~
checklength cp1 -l 7.278
checklength res -l -equal ext_1
~~~~~
@subsubsection testmanual_5_3_13 Check maximum deflection, number of triangles and nodes in mesh

To check maximum deflection, number of nodes and triangles in mesh command *checktrinfo* can be used.

Use: checktrinfo shapename [options...]

Allowed options are:
 * -tri [N]:  compare current number of triangles in "shapename" mesh with given reference data.
      If reference value N is not given and current number of triangles is equal to 0
      procedure checktrinfo will print an error.
 * -nod [N]:  compare current number of nodes in "shapename" mesh with given reference data.
      If reference value N is not givenand current number of nodes is equal to 0
      procedure checktrinfo will print an error.
 * -defl [N]: compare current value of maximum deflection in "shapename" mesh with given reference data
      If reference value N is not given and current maximum deflection is equal to 0
      procedure checktrinfo will print an error.
 * -max_defl N:     compare current value of maximum deflection in "shapename" mesh with max possible value
 * -tol_abs_tri N:  absolute tolerance for comparison of number of triangles (default value 0)
 * -tol_rel_tri N:  relative tolerance for comparison of number of triangles (default value 0)
 * -tol_abs_nod N:  absolute tolerance for comparison of number of nodes (default value 0)
 * -tol_rel_nod N:  relative tolerance for comparison of number of nodes (default value 0)
 * -tol_abs_defl N: absolute tolerance for deflection comparison (default value 0)
 * -tol_rel_defl N: relative tolerance for deflection comparison (default value 0)
 * -ref [trinfo a]: compare deflection, number of triangles and nodes in "shapename" and in "a"

Note that options -tri, -nod, -defl do not work together with option -ref.

Examples:

comparison with some reference values
~~~~~
checktrinfo result -tri 129 -nod 131 -defl 0.01
~~~~~

comparison with another mesh
~~~~~
checktrinfo result -ref [tringo a]
~~~~~

comparison of deflection with max possible value
~~~~~
checktrinfo result -max_defl 1
~~~~~

to make sure that current values are not equal to zero
~~~~~
checktrinfo result -tri -nod -defl
~~~~~

to make sure that number of triangles and number of nodes are not equal to some specific values
~~~~~
checktrinfo result -tri !10 -nod !8
~~~~~

it is possible to compare current values with reference values with some tolerances.
Use options -tol_\* for that.
~~~~~
checktrinfo result -defl 1 -tol_abs_defl 0.001
~~~~~